Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We've discovered this article on Installing A Bathtub below on the net and believe it made sense to write about it with you here.
Mounting a bath tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is likewise a reasonably challenging project. If the old bathtub is easily easily accessible, the project can relocate easily; if you have to open up a wall surface to eliminate the old tub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also embeded in the new one. See to it you have actually qualified yourself for the task and also fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is much better to consider utilizing one before you begin. Opportunities are you might need a specialist plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your bathroom if you have actually already bought a brand-new tub and do not require to change the setup of your previous water pipelines.
Your devices and also product checklist should make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing taps can be quite troublesome because of the limited gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in place between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous kind should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using the two wood boards under its feet, put the bathtub in the called for position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub till the level reviews degree.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water supply as well as examine all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and also check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has been utilized at least when as this will certainly settle it into its last setting.
Planning for the Installation
Firstly, the supporting framework provided with the bath must be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall between the bath and the tiling, bring about difficulties with dampness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack relatively early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that article on How to Install a Bathtub through a friend on our other web address. Don't hesitate to take the opportunity to distribute this blog posting if you enjoyed reading it. Many thanks for your time invested reading it.
Reliable help, dial now. Report this page